TEMI880控制器的操作图示_技术交流_仪器仪表技术文献

▶ TEMI880 is easy to install & modify by touch screen as well as the map type menu. User enablesto grasp the operation of control system with easy through graph on vivid LCD screen.

1.1.1Initial setup button

▶ Table 1-1. General Setting Button

No.	Button		Function
1	Main	Change the page.
2	General execute button	It is used general execution orselection.
3	Page Up/Down button	It is used page conversion on thesame screen.
4	Next page button	It is used to convert to next page.
5	Setting value ｓelect button	It is used setting value selection.
6	Setting value input button	Convert to setting value inputscreen.

1.1.2Input setting value

▶ If user push setting value input button in the Table 1-1（General Setting Button）, User can input

data value.

▶ If user input data which is invalid, it makes 3 times buzzer, also there is “-LIMIT ERR” messageon the setting value screen.

① Input key for the Digit setting②Input key for the Pattern & DI Error name setting

Touch Key Unlock

▶ If KEY LOCK is ON, Not input setting value. Therefore, Input setting value after KEY LOCKconvert OFF.

▶ For more information, See 1.6 Operation Setting Screen.
1.1.3Input error

▶ User can check a number of buzzer times.

1 time : Succeed set the data.

3 times : Failed set the data or the operation order is impropriety,or the key is locked .

Notice Items.

▶ Using the touch screen. Please do not use any pen/pencil, nail or any other sharp material.Otherwise, the touch screen might be broken or out of order.

▶ In order to avoid invalid input. When you set the parameter,Please according to the order High ,Middle, Low, where it is needed.

1.2 Input Setting Value

▶ All of the Input value is setting by use setting value, pattern name ａnd time signal input key.

▶ If user push setting value input button in the Table 1-1（General Setting Button）, User can input

data value.

▶ For the Pattern Name input key, See 1.9.6 Pattern Name Setting Screen.

1.2.1Function of setting value input key

① ⑨⑧

③

② ④

⑦

⑥⑤

Figure 1-1. Function of setting value input key

① Parameter.

② Valid data range.

③ “ERROR!”will be displayed when user input invalid setting value.

④ Cancel input setting value.

⑤ Clear input data.

⑥ Decimal point.

⑦ Save input data ａnd go to main page.

⑧ Modify the input data, ｄelete one by one.

⑨ Input sign（+ or -）.

1.3 Block diagram of the basic processing

Power On

【 PROG STOP】【Initial Screen】

【FIX STOP】【Main Screen】

【DI TROUBLE SCREEN】【PROGRAM SET】

1.4 Main Screen

▶ This screen is center of the total screen transfer.

Figure 1-2. Main Screen

No.	Contents	Description	Additional
j	Operation Screen	Transfer operation screen.	▶ See 1.5 Operation Screen
k	Set Function	Transfer function ａnd FIX settingscreen.	▶ See 1.6 Operation Setting Screen
l	Set Reserve	Transfer reserve setting screen.	▶ See 1.7 Reserve Setting Screen
m	Display Graph	Transfer graph setting screen.	▶ See 1.8 Graph Setting Screen
n	Set Pattern	Transfer pattern setting screen.	▶ See1.9 Pattern Setting Screen
o	Set Display	Transfer display setting screen.	▶ See 1.10 Display Setting Screen

1.5 Operation Screen

▶At the running TEMI880, Display status ａnd information.

1.5.1Program Stop Screen

Figure 1-3. PROG STOP Screen

①⑧

②⑦

③⑥

④⑤

No.	Contents	Description	Additional
①	Main Button	Transfer to 1.4 Main Screen.
②	Pattern No.	Display running pattern number.	▶ Push button ａnd set pattern number for operating.
③	Segment	Display programmed segment count of the present pattern.	▶ Program pattern input at 1.9.1 Edit Pattern Screen.
④	Time Button	Display present time. Time button is pushed, turn off LCD screen. Even if turn off the light automatically, controller still working ａnd turn on the light if user touch any point.	▶ Automatic turn off setting time at 1.6 Operation Setting Screen. ▶ Backlight time is setting 10 minutes. ▶ Present time is setting at1.7 Reserve Setting Screen.
⑤	RUN Button	Display confirmable box for program running.	▶ See （Figure1-4）.
⑥	Present Humi.	Display present humidity.
⑦	PresentTemp.	Display present temperature.
⑧	Next Button	Transfer to Figure 1-15	▶ See 1.5.5.1 Monitor Graph Screen

Confirmable Box

At this CONFIRM window, you can confirm if you really wantdoing job or not.

예） PROG（or FIX） STOP ↔ PROG（or FIX） RUN

HOLD, STEP, TUNING OFF ↔ HOLD, STEP, TUNING ON

pattern copy, pattern ｄelete etc.

Figure 1-4. PROG STOP – ConfirmFigure 1-5. PROG STOP – Pattern End

①②

Figure 1-6. PROG STOP – Reserved

③

④⑤

No.	Contents	Description	Additional
①	Confirmable Box	Program run or not.	▶ Clicked YES button : Program Start ▶ Clicked NO button : Transfer at Figure 1-3.
②	Pattern End	Blinking at the end of setting program.	▶ if user touch any point, PT END disappear. ▶ If Pattern End message is disappeared,Relay status transfer into OFF.
③	Start Run Time	Display start run time at setting reservation.	▶ The reserved time must be later than present time.
④	Reservation	Blinking at setting reservation.	▶ See 1.7 Reserve Setting Screen
⑤	RUN Button	Reserve status，Press this button to run at once.	▶ Press this button，Reservation will be canceled,and transfer at running status.

1.5.2Program Run Screen

①

Figure 1-7. Program Run – First Screen

②

③

⑤

④

⑥

⑦

⑧⑨⑩

No.	Contents	Description	Additional
①	Pattern Name	Display pattern name of the present running.	▶ See 1.9.6 Pattern Name Setting Screen
②	Next Button	Transfer at Figure 1-8.
③	Temp. Status Display Lamp	Display present Temp. status.
④	Humi. Status Display Lamp	Display present Humi. status.
⑤	Temp. SP Value	Display present Temp. SP（Set Point）.
⑥	Humi. SP Value	Display present Humi. SP（Set Point）.
⑦	Pattern/Segment	Display pattern ａnd segment number.
⑧	Hold Button	Hold on or off.	▶ Hold button’s color transferred to Blue at HOLD ON.
⑨	Step Button	Present segment stop running, Move next segment.
⑩	Stop Button	Display confirmable box.
11	Running Time	Display total running time.

Figure 1-8. Program Run – Second Screen

⑧

①②

③

④⑦

⑤

⑥

No.	Contents	Description	Additional
①	Temp. MVOUT	Display Temp. MVOUT.
②	Humi. MVOUT	Display Humi. MVOUT.
③	Running Pattern	Display program pattern and segment number.
④	Pattern Repeat	Display pattern repeat status. repeated ｃount / total repeat count	▶ See 1.9.2Repeat Setting Screen
⑤	Segment Repeat	Display segment repeat status. repeated ｃount / total repeat count	▶ See 1.9.2Repeat Setting Screen
⑥	Remain Time	Display remain time of the present running segment.
⑦	Status Display Lamp	ON status : Red. OFF status : Gray.
⑧	Next Button	Transfer at Figure 1-15.	▶ See 1.5.5.1 Monitor Graph Screen TEMI850 Tranfer at Figure1-7.

1.5.3Fix Stop Screen

Figure 1-9. Fix Stop ScreenFigure 1-10. Fix Stop – Confirm

① ② ③

Figure 1-11. Fix Stop – Time EndFigure 1-12. Fix Stop – Reserved

④⑤⑥

No.	Contents	Description	Additional
①	Temp. SP Value	Display present Temp. SP （Set Point）.	▶ See 1.2 Input Setting Value Input SP（Set Point）.
②	Humi. SP Value	Display present Humi. SP （Set Point）.	▶ See 1.2 Input Setting Value Input SP（Set Point）.
③	Time	Display present Time,Same as program.	▶ See1.5.1 Program Stop Screen
④	Fix Run Stop	Blinking at Fix Stop.	▶ See 1.6 Operation Setting Screen ▶ if user touch any point, FIX END disappear.
⑤	Reservation	Blinking at setting reservation.	▶ See 1.7 Reserve Setting Screen
⑥	RUN Button	Reserve status，Press this button to run at once.	▶ Press this button，Reservation will be canceled,and transfer at running status.

1.5.4Fix Run Screen

Figure 1-13. Fix Run – First ScreenFigure 1-14. Fix Run – Second Screen

jkl

No.	Contents	Description	Additional
j	T-AT	Temp. side : Auto Tuning On/Off.	▶ T-AT button’s color transferred to blue at Auto Tuning of the Temp. side.
k	H-AT	Humi. side : Auto Tuning On/Off.	▶ H-AT button’s color transferred to blue at Auto Tuning of the Humi. side.
l	PID Group No.	Display PID Group No.
m	Next Button	Transfer at Figure 1-15.	▶ See 1.5.5.1Monitor Graph Screen TEMI850 Tranfer at 1-13

1.5.5Monitor graph & attribute .

1.5.5.1 Monitor Graph Screen

▶ This function is only for TEMI880.

Figure 1-15 Monitor Graph Screen

No.	Contents	Description	Additional
j	NEXT Button	If Prog Running,Transfer to Figure 1-7 Program Run – First Screen； If Fix Running, Transfer to Figure 1-13 Fix Run – First Screen.	▶ See Figure 1-7 Program Run – First Screen ▶ See Figure 1-13 Fix Run – First Screen
k	PAR. Button	Tranfer to Monitor Graph Attribute Setting Screen.	▶ See 1.5.5.2 Monitor graph attribute setting.
l	DEL Button	Delete Monitor Graph。	Deleted Graph won’t be resumed.
m	TEMP Graph Display or not Button.	To ｓelect Display or Hide TEMP PV ａnd SP。	▶ TEMP PV: In Red。 ▶ TEMP SP: In Green。
n	HUMI Graph Display or not Button.	To ｓelect Display or Hide HUMI PV ａnd SP。	▶ HUMI PV: In blue。 ▶ HUMI SP: In black。
o	LEFT Move Button	Left move window,to see earlier Graph.
p	RIGHT Move Button	Right move window,to see later Graph.

1.5.5.2 Monitor graph attribute setting.

Figure 1-16 Monitor Graph Attribute Setting Screen

①

②

③

④

⑤

No.	Contents	Description	Additional
j	EXIT Button	Back to Monitor Graph Screen.
k	Sample period.	Select a sample period for Monitor Graph.Because of the limited space of memorizer of TEMI880.different Sample period will bring on different record time.	▶ Limited Record Time： 1s：6 hours. 10s：60 hours. 30s：180 hours. 60s：360 hours.
l	FIN. MODE	STOP：Space used up,stopping record at once. REP.：（Repeat） When space used up, record operation will continue,but the old record will be coverd
m	TEMP RANGE	Set a Y coordinate for Temp,Range High,and Range Low	▶ Different range width will bring a different outline effect of the Graph.
n	HUMI RANGE	Set a Y coordinate for Humi,Range High,and Range Low

1.6 Operation Setting Screen

▶ This is the screen about additional function of the general machine ａnd additional setting at Fix Run.

Figure 1-17. Operation Setting – First Screen

①

②

③

No.	Contents	Description	Additional
j	Operation Mode	Select Program mode or Fix mode.	▶ PROG : 1.5.1 Program Stop Screen ▶ FIX :1.5.3 Fix Stop Screen ☞ It isn’t changed at the running.
k	Power Mode	Setup when re-start after power off. ▶ Recognize to power off if it is more than 3 seconds. ▶ If re-start before 3 seconds, It will run to Hot mode Automatically.	▶ The running after power on
			Before Power Off	PROG/FIX STOP	PROG RUN	FIX RUN
			STOP	PROG/FIX STOP	PROG STOP	FIX STOP
			COLD	PROG/FIX STOP	Run from first segment.	FIX RUN
			HOT	PROG/FIX STOP	Run from running segment time before power off.	FIX RUN
l	Key Lock	Key Lock/Unlock.
m	LightTime	Set time of the backlight.	▶ The default backlight time is setting 10 minutes.

Figure 1-18. Operation Setting – Second Screen

①

②

③

④

⑤

No.	Contents	Description	Additional
j	Operation Hour（H）	Set Hour.
k	Operation Minute（M）	Set Minute.
l	Time Mode	Set Time Mode On/Off.	▶ OFF : Fix running is stopped at the STOP button clicked. ▶ ON : It is stop after running time （set j,k） automatically.
m	Temp. Slope	Temp. up/down slope.	▶ Temp./Humi. value goes to the SP gradually. It is applied both of up ａnd down.
n	Humi. Slope	Humi. up/down slope.

1.7 Reserve Setting Screen

▶ This is the screen about time ａnd reserved operation setting.

Figure 1-19. Reserve Setting Screen

①

②

③

No.	Contents	Description	Additional
j	Current Time	Set ａnd display present date & time.
k	Reserve Time	Set ａnd display reservation date & time.
l	Reserve Mode	Select Reservation On or Off.	▶ See Figure 1-6, Figure 1-12

1.8 Graph Setting Screen

▶ This is screen display graph for the input pattern at 1.9.1 Edit Pattern Screen.

Figure 1-20. Graph Setting Screen

①

②

③

④

⑤

⑥

No.	Contents	Description	Additional
j	TIME Button	Change time scale.	▶ Push time button => change time scale.
			0H 1H 2H 3H 4H
			↓
			0H 3H 6H 9H 12H
			↓
			0H 6H 12H 18H 24H
			↓
			0H 12H 24H 36H 48H
			↓
			0H 24H 48H 72H 96H
k	MAIN	Transfer to Main Screen	▶ See 1.4 Main Screen
l	Pattern No.	Set pattern number.
m	TEMP SP	Display/Hide Temp SP Graph。	▶Temp. SP : Display red.
n	HUMI SP	Display/Hide Humi SP Graph。	▶ Humi. SP : Display blue.
o	Previous/Next Button	Move previous/next page.	▶ See1.5.5.1 Monitor Graph Screen .

1.9 Pattern Setting Screen

▶ This is the screen about pattern setting.

Figure 1-21. Pattern Setting Screen

⑦

No.	Contents	Description	Additional
j	PROG Pattern EDIT	Move toedit pattern screen.	▶ See 1.9.1 Edit Pattern Screen
k	Set Repeat	Move torepeat setting screen.	▶ See 1.9.2 Repeat Setting Screen
l	Edit File	Move to edit file screen.	▶ See 1.9.3 Edit File Screen
m	Time Signal	Move totime signal setting screen.	▶See 1.9.4 Time Signal Seeting Screen
n	Set Wait	Move towait operation setting screen.	▶See 1.9.5 Wait Operation Setting Screen
o	Pattern Name	Move topattern name setting screen.	▶See 1.9.6 pattern name setting screen.
⑦	Message	Move to Prog File Message Screen.	▶ See1.9.1.5Prog File Message Screen

1.9.1Edit Pattern Screen

Figure 1-22. Edit Pattern Screen

nopq

No.	Contents	Description	Additional
j	Segment No.	A case where ｉnsert or delete segment, Clicked this button.	▶ Segment color is displayed green at the buttonclicked. In this case, you can segmentｉnsert or delete.
k	Segment Temp.	Set segment temperature.
l	Segment Humi.	Set segment humidity.
m	Segment Time	Set segment time.	▶ Input method of the time.
			Set Time	Display
			OFF	-0.01
			1 minute	0.01
			30 minutes	0.30
			1 hour	1.00
n	PG UP	Move previous page.	▶ See1.9.1.3 Move Screen
o	PG DN	Move next page.	▶ See1.9.1.3 Move Screen
p	Insert Segment	Insert segment.	▶ See 1.9.1.1 Insert Method of the Segment
q	Delete Segment	Delete segment.	▶ See 1.9.1.2 Delete Method of the Segment
r	Time Signal	Set time signal.	▶ See 1.9.1.4 Set Method of the Time Signal ▶ See 1.9.4 Time Signal Setting Screen
s	Pattern No.	Set pattern number.	☞ Change pattern number of 1.9.2 Repeat Setting Screen

you are not able to edit a prog pattern when it is running.If you attempt to do this,

TEMI880 will buzz “bi bi”to alarm.

1.9.1.1 Insert Method of the Segment

▶ Example => Insert segment.

Figure 1-23. Before Insert SegmentFigure 1-24. After Insert Segment

1） Clicked “2”areas of Figure 1-23, then the background of “2” character color is changed green to indication editable status.

2） Clicked ｉnsert button（p ） of Figure 1-22. Edit Pattern Screen, a segment of the same value is

Inserted,behind Segment 2.

1.9.1.2 Delete Method of the Segment

▶ Example => Delete segment.

Figure 1-25. Before Delete SegmentFigure 1-26. After Delete Segment

1） Clicked “2”areas of Figure 1-25, then the background of “2” character color is changed green to indication editable status.

2） Clicked ｄelete button（q） of Figure 1-22. Edit Pattern Screen, “2” segment is deleted.

A case where segment do not ｉnsert or delete.

When a prog pattern is running.

1.9.1.3 Move Screen

obutton of Figure 1-22. Edit Pattern Screen

nbutton of Figure 1-22. Edit Pattern Screen

1.9.1.4 Set Method of the Time Signal

▶ This is the screen about time signal setting.

Figure 1-27. Before Time Signal Setting

①

As Figure 1-27 above，Clickeddot-rectangle areas of（①），will display Figure

1-28. Time Signal Setting Key.

Figure1-28. Time Signal Setting Key.

1） SEGx: Indicate the segment No.of a Prog（1 ～ 100）

2） TSx: Indicate one of TS（TS1～ TS4）of this segment of the prog.

3） Input a number , the range is form 0 to 7.（0 ～ 7）.then press ENT.

A kind of the input time signal : See 1.9.4 Time Signal Setting Screen.

1.9.1.5 Prog File Message Screen

▶ Display number of the used pattern ａnd segment.

Figure 1-29. File Information Screen

▶ How many Progs ａnd Segments have been used will be displayed in this screen.

▶ Press“PRO.SET”to move to Figure 1-21 Pattern Setting Screen.

1.9.2Repeat Setting Screen

Figure 1-30. Repeat Setting Screen

No.	Contents	Description	Additional
j	Pattern No.	Set pattern number.	Change pattern number of 1.9.1 Edit Pattern Screen.
k	Pattern Repeat No.	Set pattern repeat number.	“0” is repeating unlimitedly.
l	Link Pattern	When the finish the runningpattern, set the next patternnumber continually.	“0” is no Link pattern.
m	Start Segment parts.	Set the start segment numberof repeat	▶ Notice: Start Segment ≤ End Segment, Otherwise,system will buzz “bi bi” to alarm.
n	End Segment	Set the end segment numberof repeat parts.
o	Count Segment	Set the number of repeat parts.

1.9.2.1Set Pattern Repeat

Set value of the pattern repeat	Process order
▶ Repeat 3 times Pattern 1，then jump to Pattern 2.
▶ Repeat 5 times Pattern 3，then jump to Pattern 4.
▶ Repeat 5 times Pattern 3,then stop.
▶ Repeat Pattern 3 forever. PT CYC = 0，Indicate repeat this pattern forever,even if a valid LINK PT NO is setted
▶ Repeat Pattern 1 forever. Link to the pattern itself，though PT CYC =3,it is inessential.

1.9.2.2 Process Order about Setting Method of the Repeat Parts（Segment Repeat）

▶ Examples,

▶ It is assumed a pattern has already setted its 1 segment ~ 8 segment（01 → 02 → 03 → 04 → 05 → 06 → 07 →08）

No.	Set value of the repeat parts	Process order
Example 1		① 01→02→03→04 ② 02→03→04 ③ 03→04→05 ④ 03→04→05 ⑤ 01→02→03→04 ⑥ 01→02→03→04 ⑦ 04→05→06 ⑧ 04→05→06→07→08
Example 2		① 01→02→03→04 ② 02→03→04 ③ 04→05→06 ④ 04→05→06→07→08
Example 3		① 01→02→03→04→05→06→07→08 ② 07→08 ③ 04→05→06 ④04→05→06→07→08
Example 4		① 01→02→03→04→05 ②03→04→05→06→07→08
Example 5		① 01→02→03→04→05→06→07 ②03→04→05 ③03→04→05→06→07→08
Example 6		① 01→02→03→04→05→06→07 ② 05 ③ 05→06→07→08
Example 7	① 01→02→03→04→05→06→07→08

1.9.3Edit File Screen

Figure 1-31. Edit File Screen

No.	Contents	Description	Additional
j	Source Pattern	Set source pattern number.
k	Destination Pattern	Set destination pattern number.
l	Delete Pattern	Set pattern number for elimination.
m	Delete Result	Delete Result indication.
n	Execute Result	Display execute result.
o	Pattern Copy Button	Pattern copy.	▶ Copy Source Pattern to Destination Pattern. ▶ You can not copy if source pattern is empty.
p	Pattern Delete Execute Button	One Pattern Delete operation.	Deleted Pattern can’t be resumed.
q	All Pattern Delete Execute Button	All Pattern Delete operation.	Deleted all Pattern can’t be resumed

1.9.4Time Signal Setting Screen

Figure 1-32. TS Setting – First ScreenFigure 1-33. TS Setting – Second Screen

① ②

No.	Contents	Description	Additional
①	On Time	Set wait time for the time signaloutput.	▶ See 1.9.1.4. Set Method of the Time Signal▶ NO : 00 → No use time signal. ▶ NO : 01 → Use time signal. ▶ NO : 02 ~ 07 → Use time signal from On time to Off time.
②	Off Time	Set running time for the time signal output.

Time Signal Operation
▶ Set value of the program pattern			▶ Set value of the time signal
▶ Time signal operation within segment
Setting		Time signal operation
N SEG TIME >= ON TIME + OFF TIME ☞ It has not influence on next segment.	1.ON TIME =00.00 OFF TIME = 04.00 （Time SignalNo:04 ）
	2. ON 时间 = 02.00 OFF 时间 = 02.00 （Time Signal:05）
N SEG TIME < ON TIME + OFF TIME	2.ON 时间=00.00 OFF 时间 = 10.00 （Time Signal:06）
	3.ON 时间 = 04.00 OFF 时间 = 06.00 （Time Signal:07）

1.9.5Wait Operation Setting Screen

Figure 1-34. Wait Operation Setting Screen

No.	Contents	Description	Additional
j	Wait Mode	Set On/Off for using Wait.	▶ “OR” Condition → Temp. or Humi. PV does not reachthe wait area before Wait Time. ▶ “AND” Condition → Temp. ａnd HUmi. PV reach the wait area before Wait Time.
k	Temp. Zone	Set a Temp. zone.
l	Humi. Zone	Set a Humi. zone.
m	Wait Time	Set a Wait time.	▶ Initial time （00.00） → Wait to infinity.

The relation of the wait operation ａnd wait time

▶ WAIT ZONE : Temperature → TEMP ZONE, Humidity → HUMI ZONE.

① A case where wait release within Wait Time

②A case where PV does not enter WZ（Wait Zone） within Wait Time

1.9.6Pattern Name Setting Screen

Figure 1-35. Pattern Name Setting Screen

No.	Contents	Description	Additional
j	Pattern Name Button	Set pattern name.	▶ Max : use 10 character.
k	Page Move Button	Move pattern page.	▶ 1 Page : Display 5 pattern name.

1.9.6.1 The Method of the Pattern Name Setting

▶ The example of the pattern 02name setting : “PROG2”.

Figure 1-36. Before Pattern Name Setting

⑥⑤

Figure 1-37. Pattern Name Setting Key

①

② ③④⑦

▶ If user touch dot-rectangle areas（①） of Figure 1-36. Before Pattern Name Setting, Display Figure1-37. Pattern Name Setting Key.

▶ The order of the pattern name setting :③→③→⑤→②→⑤→⑤→④→⑥→⑤→⑤→⑤→⑦。

1.10 Display Setting Screen

▶ This is the screen of the display setting.

Figure 1-38. Display Setting Screen

①

②

③

No.	Contents	Description	Additional
j	MAIN Button	Move to Main Screen.	▶ See 1.4 Main Screen
k	Tuning Key	Display or hide AT button.	▶ Display or hide T-AT/H-AT button of the Figure 1-13. Figure1-14
l	Refresh Frequency	Adjust the LCD’s Refresh Frequyncy	▶ Factory used to debug only,not recommend user or the third party to adjust it.