GP2Y1010AU0F detects particles in the air by optical sensing.Properties:-Operates on 5 Volt-Current dissapation of less than 20 mA-0-0.6 mg/m3(cubic meter) range-Enable to distinguish smoke from house dust
An infrared emiiting diode and a phototransistor are diagonally arranged. Light reflects on the particles passing through the whole are picked up by the photodiode(PD) is transformed into voltage. The voltage has to be amplified to be able to read the change. You can change the resistance of the RS(variable resistor) in the amplifier circuit to make it more sensitive but if you do so, note that you can't reference output voltage vs. dust sensity at fig.3 (below)
![]() | ![]() |
Image byShinyei | GP2Y1010AU Internal Schematic |
These results are true only when the sensor is used with factory settings. The variable resistor shouldn't be changed.Attach:output.jpg ΔThe table demonstrates that for every 0.1 mg more of dust, the voltage increases by 0.5 Volts.There are other environmental sensors in the market that can detect particles with the size of 1 micrometer (1μm). This scale means that even pollen grains, and mildew spores can be detected. There is no information about this on GP2Y1010AU's datasheet except that it is stated that it can detect cigarette smoke.0.6 mg/m3 of dust doesn't seem much when National Institute for Occupational Safety and Health (NIOSH)'s recommended wood dust is 1 mg/m3 and used to be 5mg/m3 for softwoods.
Applications-Air purifier-Air monitor for industry-Device dust alert-Fire Alarm (although Sharp Electroics wants to be informed if used in such system.)More unusual apps:-Vacuum cleaner robotas inthis guy's paper
Setup and CodeSetup is very straight-forward except the soldering. 6 pin connector header is small and very closed. I had to break one side of the header housing.One important thing about the code is in order to turn the ILED on, you have to digitalWrite LOW on LED input terminal. Because the transistor that opens the drain is PNP type of transistor which needs negative base voltage.I also added a buzzer which goes off when it detects smoke.
Arduino codeProcessing Visualization
In most of these tests, I had watch if the smoke/dust went inside the whole.Test1: Putting off a match
![]() | ![]() |
Test2: Cigarette Smoke
![]() | ![]() |
Test3: Burning Paper
![]() | ![]() |
Test4: Dust from my Rug
![]() | ![]() |
I was confused with the results because I wasn't expecting such high values from the 4th test where i just had some dust falling from my rug. Ok, i admit my rug hasn't been washed for a while but the voltage should only go up when the density is high, and compared to smoke, dust wasn't dense at all.
参数: | |
· | 物镜:10×消色差 |
· | 目镜:20×带0.1mm格值分划板 |
· | 测量承座:Φ25×10mm |
90°剥离试验机应用领域:90度电动剥离试验机专门用于实验PC板上铜箔电路之附力,或锡箔、铜箔、胶布...等,粘着干物体表面之牢度。试验时以垂直之角度剥离试料,剥离运行速度可调,测得实际粘结之强度。设有微动开关,能任意设定剥离行程。
90°剥离试验机产品相册:
90°剥离试验机参数规格
1. 测试角度:90°
2. 测试荷重:0—50kg
3. 速度:5—100mm/分
4. 测试行程:350mm
5. 重量:约40kg
6. 电源:AC220V,2A
7. 体积:约660*340*670mm
8. 数显式推拉力计: 最大拉力50KG
90°剥离试验机产品特点:
1、专为垂直剥离测试设计制作,设计合理,结构紧固,运行安全、稳定、精确;
2、电动式操作,梯型螺杆传动,结构牢固,运行稳定,无噪音;
3、试验速度可调,具有限位装置,可自动停止运行;
4、可选配数显/指针推拉力表及各类工装夹具,测试范围广泛。
90°剥离试验机使用方法
1.使用前必须放在稳固的台面上,
2.不允许在使用过程中搬弄机台;
3.选择相应电源电压,切勿过高,避免烧坏器件;
4.在仪器出现异常时,请与本所联系以便及时处理;
5.机器工作时必须有良好的通风环境。
6.按键机械各组件,由于运转负荷较大,机械部分请及时加润滑油;
7.每次试验完毕,清理机台,保持机台清洁;
8.控制箱部分,须以干布擦拭,不可用湿布。
厦门德仪设备有限公司专业生产的环境试验设备主要适用于:塑胶橡胶、纸品、包装、印刷、胶粘带、五金电子、玩具、家俱、鞋类、婴儿用品等众多行业。并且适用于各种科研单位、质检机构、研究所、高校学术探讨等各大领域。公司主要研发、制造和销售的环境试验设备有:高低温交变湿热试验箱、高低温交变试验箱、高低温箱、恒温恒湿试验箱、步入式恒温恒湿室、换气式老化箱、冷热冲击试验箱、紫外线老化箱、氙灯老化试验箱、臭氧老化箱、盐雾试验箱、淋雨试验箱、砂尘试验箱、耐黄变试验箱、超低湿常温干燥箱、电子防潮柜,低温低湿干燥箱、真空干燥箱、电热鼓风干燥箱、跌落试验机、调频扫频振动试验台、拉力试验机等环境试验设备。产品完全符合UL、ASTM、JIS、GB、ISO、TAPPI、EN、DIN、BS……等国际标准。
RK2681A型绝缘电阻测试仪
主要技术指标:电阻测试范围:100KΩ~10TΩ测试度: R<1GΩ:3%读数+0.5格 ≥1GΩ:5%读数+0.5格 ≥1TΩ:10%读数+0.5格测试电压: 10V/50V/100V 250V/500V/1000V电压度:2%测量电流范围:≤100UA控制方式:模拟电路触发方式:无量程方式:手动测试速度:阻性元件:<0.5秒容性元件:0.5~1.0秒分选:合格,不合格及不合格讯响(可开关)
| |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||