Plant Arg-1 ELISA Kit instruction

Intended use

This Arg-1 ELISA kit is intended Laboratory for Research use only ａnd is not for use in diagnostic or therapeutic procedures.The Stop Solution changes the color from blue to yellow ａnd the intensity of the color is measured at 450 nm using a spectrophotometer. In order to measure the concentration of Arg-1 in the sample, this Arg-1 ELISA Kit includes a set of calibration standards. The calibration standards are assayed at the same time as the samples ａnd allow the operator to produce a standard curve of Optical Density versus Arg-1 concentration. The concentration of Arg-1 in the samples is then determined by comparing the O.D. of the samples to the standard curve.

Sample collection ａnd storages

1. Can’t detect the samples which contain NaN3, because NaN3 inhibits HRP activity of the horseradish peroxidase.

   2. Extract as soon as possible after Specimen collection, Extracted according to the relevant literature.

   Cell culture supernates ａnd plant exact fluids - Remove particulates by centrifugation and assay immediately or aliquot ａnd store samples at -20°C or -80°C. Avoid repeated freeze-thaw.

   Materials required but not supplied

   1. Standard microplate reader（450nm）

   2. Precision pipettes ａnd Disposable pipette tips.

   3. 37 ℃ incubator

   Precautions

   1. Do not substitute reagents from one kit to another. Standard, conjugate and microplates are matched for optimal performance. Use only the reagents supplied by manufacturer.

   2. Do not remove microplate from the storage bag until needed. Unused strips should be stored at 2-8°C in their pouch with the desiccant provided.

   3. Mix all reagents before using.

   Remove all kit reagents from refrigerator ａnd allow them to reach room temperature （ 20-25°C）

   Materials supplied

Note: Standard （S0 → S5） concentration was followed by: 0,1,2,4,8,16 ng/mL

Reagent preparation

20×wash solution:Dilute with Distilled or deionized water 1:20.

Assay procedure

1. Prepare all reagents before starting assay procedure. It is recommended that all Standards and Samples be added in duplicate to the Microelisa Stripplate.

2. Add standard: Set Standard wells, testing sample wells. Add standard 50µl to standard well.

3. Add Sample: Add testing sample 10µl then add Sample Diluent 40µl to testing sample well; Blank well doesn’t add anyting.

4. Add 100µl of HRP-conjugate reagent to each well, cover with an adhesive strip and incubate for 60 minutes at 37°C.

5. Aspirate each well ａnd wash, repeating the process four times for a total of five washes. Wash by filling each well with Wash Solution （400µl） using a squirt bottle, manifold dispenser or autowasher. Complete removal of liquid at each step is essential to good performance. After the last wash, remove any remaining Wash Solution by aspirating or decanting. Invert the plate ａnd blot it against clean paper towels.

6. Add chromogen solution A 50µl ａnd chromogen solution B 50µl to each well. Gently mix and incubate for 15 minutes at 37°C. Protect from light.

7. Add 50µl Stop Solution to each well. The color in the wells should change from blue to yellow. If the color in the wells is green or the color change does not

appear uniform, gently tap the plate to ensure thorough mixing.

8. Read the Optical Density （O.D.） at 450 nm using a microtiter plate reader within 15 minutes.

Calculation of results

1. This standard curve is used to determine the amount in an unknown sample. The standard curve is generated by plotting the average O.D. （450 nm） obtained for each of the six standard concentrations on the vertical （Y） axis versus the corresponding concentration on the horizontal （X） axis.

2. First, calculate the mean O.D. value for each standard ａnd sample. All O.D. values, are subtracted by the mean value of the zero standard before result interpretation. Construct the standard curve using graph paper or statistical software.

3. To determine the amount in each sample, first locate the O.D. value on the Y-axis ａnd extend a horizontal line to the standard curve. At the point of intersection, draw a vertical line to the X-axis ａnd read the corresponding concentration.

4. Any variation in operator, pipetting ａnd washing technique, incubation time or temperature, ａnd kit age can cause variation in result. Each user should obtain their own standard curve.

5. The sensitivity by this assay is 0.1 ng/mL

6. Standard curve

   Storage： 2-8℃.

   validity： six months.

   FOR RESEARCH USE ONLY; NOT FOR THERAPEUTIC OR DIAGNOSTIC APPLICATIONS! PLEASE READ THROUGH ENTIRE PROCEDURE BEFORE BEGINNING!