森东宝探针台
森东宝探针台配件
美国GGB探针：直流探针、射频探针
- Model 110H
- Model 40A
- Model 12C
- Model 7 and Model 7A
- Model 40M
- Model 50A
- 校准片
- Model 67A
- Integrated Balun Probes
- Multi-Contact Wedge
- Probe Cards
- Model 50
- Model 75
- Model 90
- Model 120
- Model 140
- Model 220
- Model 170
- Model 325B
- Model 500B
- Model 1100B
- Model 10 (dc to 11 GHz )
探针座
光学平台
液晶屏激光修复仪
Bias Tees
探针夹具
屏蔽箱
转接头
显微镜
气体放电与等离子体诊断仪
联系我们
联系人：向文梅
技术文章
深圳GGB model7高频探针夹具
点击次数：828 发布时间：2017/5/23 9:04:02
商家名片
向**
联系我时，请说明是阿仪网看到的，谢谢!
- 电话: 18******958
- 手机: 18******958
- 微信:
- 交换名片后展示联系方式 → →
产品简介
具GGB model 7 ａnd model 7A
6英尺长线缆，50欧姆阻抗，直流到500MHz
PICOPROBE® MODEL 7 was designed as a companion probe to Models 12C
ａnd 18C for driving integrated circuit lines so the Model 12C ａnd 18C can be used to measure the response of adjacent nodes. The Model 7 consists of a flexible 6 foot, 50 ohm coaxial cable accurately terminated to 50 ohms in order to avoid undesirable reflections. A special miniature connector receives replacement coaxial probe tips that provide a shielded environment to within 3 mm of the fine tungsten probe point, thus minimizing capacitive coupling to other parts of the circuit. The replaceable coaxial probe tips are offered in various point sizes ａnd can also be bent to any shape in order to accommodate a variety of probing geometries.
PICOPROBE® MODEL 7A, an unterminated version, can be used for capacitance ａnd resistance measurements or in low to medium speed signal applications where a 50 ohm termination is not required. A flexible coaxial cable length of 6 feet in length is standard on the Model 7A; however, when used for capacitance measurements, GGB Industries, Inc., recommends using a shorter 3 foot cable. If a shorter length of cable is desired for capacitance measurements, please specify it when ordering (Model 7A-3ft.). Please note that Model 7A uses Model 7 replacement tips.
model7 的替换探针有以下类型：
具GGB model 7 ａnd model 7A
6英尺长线缆，50欧姆阻抗，直流到500MHz
PICOPROBE® MODEL 7 was designed as a companion probe to Models 12C
ａnd 18C for driving integrated circuit lines so the Model 12C ａnd 18C can be used to measure the response of adjacent nodes. The Model 7 consists of a flexible 6 foot, 50 ohm coaxial cable accurately terminated to 50 ohms in order to avoid undesirable reflections. A special miniature connector receives replacement coaxial probe tips that provide a shielded environment to within 3 mm of the fine tungsten probe point, thus minimizing capacitive coupling to other parts of the circuit. The replaceable coaxial probe tips are offered in various point sizes ａnd can also be bent to any shape in order to accommodate a variety of probing geometries.
PICOPROBE® MODEL 7A, an unterminated version, can be used for capacitance ａnd resistance measurements or in low to medium speed signal applications where a 50 ohm termination is not required. A flexible coaxial cable length of 6 feet in length is standard on the Model 7A; however, when used for capacitance measurements, GGB Industries, Inc., recommends using a shorter 3 foot cable. If a shorter length of cable is desired for capacitance measurements, please specify it when ordering (Model 7A-3ft.). Please note that Model 7A uses Model 7 replacement tips.
model7 的替换探针有以下类型：
| Model 7 ａnd Model 7A Replacement Tips | ||
|---|---|---|
| Part Number | Tungsten Probing Wire Shaft Diameter | Point Radius |
| 7-5 | 5 micron | <0.1 micron |
| 7-10 | 10 micron | <0.1 micron |
| 7-22 | 22 micron | <1.0 micron |
| 7-35 | 35 micron | <2.0 micron |
| 7-60 | 60 micron | <3.0 micron |
| 7-125 | 125 micron | <5.0 micron |
| 7-175 | 175 micron | <5.0 micron |
原创作者：深圳市森东宝科技有限公司
