山东洗地机批发价格 手推式洗地机售后完善 使用放心！

　　驾驶型洗地机不能行驶的主因有7个：

　　：机器防飞车保护系统开启

　　处理方法：驾驶者需松开加速行驶踏板，让其回位，然后关闭洗地机电源，再按下电源复位按钮，重新启动后，踩下加速行驶踏板启动洗地机即可恢复作业。

　　二：蓄电池电量不足

　　处理方法：将驾驶式洗地机没电，这时工人需要开启电磁刹车，将洗地机推至有电源的区域，进行充电。注意充电时间不可过长亦不可过短，避免损耗电池，影响电池的使用寿命。

　　三：电源接线端腐蚀损坏

　　处理方法：电源接线端如果损坏，需要断开洗地机的电源，卸下螺母，将接线端清理干净或者更换新的再重新装上。注意：如果工人不具备更换电源线端口的能力，可联系售后厂家上门，进行维护与更换。

　　四：加速器已损坏

　　处理方法：可联系售后技术人员更换，也可在售后技术人员的视频指导下自行更换，驾驶式洗地机其实结构很简单。

　　五：电接速插接件松动

　　处理方法：关闭洗地机电源，对松动处重新修复拧紧或者直接更换即可。

　　六：电磁剎线接触不良

　　处理方法：关闭电源，将电磁剎线重新接线或者更换新的即可。

　　七：开关位置不对

　　处理方法：将开关位置重新打至行驶的状态即可。

　　这些便是驾驶式洗地机无法作业行驶的基本原因与解决方法，相关设备管理者或者操机人员可仔细阅读或进行收藏，以备不时之需。

联系我们：

山东金驰清洁科技有限公司

联系电话：同号

19163220590同号

济南公司：济南市高新区世纪大道15615号

枣庄公司：滕州市善国中路42号

网址：http：//www.sdjinchi.com

　　There are seven main reasons why the driving floor washer can＇t run

　　1： The anti runaway protection system of the machine is on

　　Treatment: the driver needs to release the accelerator pedal, let it return to its position, ａnd then turn off the power supply of the floor washer, ａnd then press the power reset button. After restarting, step on the accelerator pedal ａnd start the floor washer to resume operation.

　　2： The battery is low

　　How to deal with it: when the driving floor washer has no power, the workers need to turn on the electromagnetic brake ａnd push the washer to the area with power supply for charging. Note that the charging time should not be too long or too short to avoid the loss of battery ａnd affect the service life of battery.

　　3： The power terminal is corroded ａnd damaged

　　Treatment: if the power terminal is damaged, it is necessary to disconnect the power supply of the floor washer, remove the nut, clean the terminal or replace it with a new one, ａnd then install it again. Note: if the workers do not have the ability to replace the power cord port, they can contact the after-sales manufacturer for maintenance ａnd replacement.

　　4： The accelerator is damaged

　　Treatment: you can contact the after-sales technical personnel to replace it, or you can replace it by yourself under the video guidance of the after-sales technical personnel. In fact, the structure of the driving floor washer is very simple.

　　5： Loose electrical connector

　　Treatment: turn off the power supply of the floor washer, repair ａnd tighten the loose part again or replace it directly.

　　6： Poor contact of electromagnetic brake wire

　　Treatment: turn off the power, rewire the electromagnetic brake wire or replace it with a new one.

　　7： Wrong switch position

　　Processing method: turn the switch position back to the driving state.

　　These are the basic reasons why the driving floor washer can＇t work ａnd the solutions. The relevant equipment managers or operators can read or collect them